Horizontal tapping tee, SDR 11
Horizontal tapping tee DAP SDR 11
- Gas and water
- Working pressure: MOP (gas) 10 bar, PFA (water) 16 bar
- Material: PE 100
- Conventional clamping technology (brackets and screws)
- Vertical outlet for special solutions:
- Space-saving installation
- With 90 degree elbow and ball valve = Rotatable dome 360 degrees
- Leak test possible before drilling.
- Integrated drill with upper and lower inner stop
- Sealing plug with internal sealing O-ring
- Safety technology
- DVGW test mark: DV-8601AU2248 and DV-8606AU2249
Note:
When using 100% hydrogen (H2), the DAP pressure tapping fitting must be installed with a DK sealing cap (order no. 612310).
Utilise the operating key FWSS SW 17 for d 63 (Order No. 613246) or FWSS SW 19 from d 90 (Order No. 613250).
There is a suitable pressure test adapter FWDPA for DAP (Order No. 613595).
PE 100 SDR 11
Maximum permissible working pressure 16 bar (water) / 10 bar (gas)
| Reference | d1 | d2 | d3 | L | t1 | t2 | Drilling Ø da |
Weight kg | BX | PU |
|---|---|---|---|---|---|---|---|---|---|---|
| 616042 | 63 | 32 | 40 | 125 | 50 | 84 | 21 | 0,630 | 16 | 288 |
| 615581 | 110 | 32 | 50 | 158 | 58 | 115 | 30 | 1,280 | 12 | 96 |
| 615606 | 110 | 50 | 50 | 158 | 58 | 115 | 30 | 1,340 | 12 | 96 |
| 615711 | 125 | 32 | 50 | 158 | 58 | 115 | 30 | 1,340 | 12 | 96 |
| 615712 | 125 | 50 | 50 | 158 | 58 | 115 | 30 | 1,330 | 12 | 96 |
| 615713 | 160 | 32 | 50 | 170 | 70 | 115 | 30 | 1,540 | 8 | 64 |
| 615714 | 160 | 50 | 50 | 170 | 70 | 115 | 30 | 1,560 | 8 | 64 |
| 615715 | 180 | 32 | 50 | 170 | 70 | 115 | 30 | 1,550 | 6 | 48 |
| 615716 | 180 | 50 | 50 | 170 | 70 | 115 | 30 | 1,570 | 6 | 48 |
| 615717 | 225 | 32 | 50 | 170 | 72 | 115 | 30 | 1,570 | 6 | 48 |
| 615718 | 225 | 50 | 50 | 170 | 72 | 115 | 30 | 1,590 | 6 | 48 |
FRIALEN pressure tapping tees ≤ d 63 are applicable for pipes of SDR level 11 and > d 63 for pipes of SDR level 11 to 17.6. Minimum wall thickness s minimum ≥ 3 mm. Other levels of SDR can be processed on request. Please note the mandatory labels directly on the product. DVGW test marks issued: DV-8601AU2248 and DV-8606AU2249.
Areas of Application
The FRIALEN DAP is used for HD-PE pipe systems both in the water and gas industry. The outlet spigot has been designed to be extra long. These pressure tapping tees are particularly suited for space-saving horizontal installation.
Assembly Instructions
The fusion of the HD-PE distribution pipes and the house connections with FRIALEN-Pressure Tapping Tees takes place by FRIALEN-fusing –leakproof and longitudinally strong.
The saddle and the outlet spigot have to be prepared according to the general installation instructions (see “Assembly Instructions” for “FRIALEN-Safety Fittings for house connections and distribution pipes up to d 225”). This involves removing the oxide skin and cleaning the pipe covered by the saddle.
Good reasons for using FRIALEN DAP Pressure Tapping Tees:
- Economy due to space-saving horizontal installation. Excavation depth of pipe system trenches reduced by 10-20 cm
- Protection from damage during subsequent work in the trench through the dome and outlet being positioned below the mains pipe apex
- Length of the outlet spigot measured for 2 fusions
- Additional barcode for tracing back the underground fitting (Traceability-Coding)
In addition, all tried-and-tested advantages of a FRIALEN Pressure Tapping Tee apply:
- Drill guidance through metallic threaded coupling
- No gas escapes during drilling process
- Little force required for drilling
- Secure position of the cut-out calotte in the drill
- Upper and lower end position
- Broad fusion zone
- Valve dome can be fused with the seal cap after drilling
- No shavings on drilling
- Possible to carry out leakage check before drilling
get_app
get_app
